COLE HERSEE part description

Cole Hersee intermittent and continous solenoids provide safe, dependable control of electrical systems on all type of DC low voltage vehicles. In addition, they are ideal for marine applications and for forward and reverse systems in golf carts, garden tractors, fork lift trucks and winch operation.
Solenoids are relays which are commonly used to remotely switch a heavier current. By using a solenoid, the amount of heavy wiring needed to power the load is reduced, since the control circuit mounted inside the cab typically utilizes a smaller wire gauge.
Housing are available in plated steel, phenolic or plasticized steel. A latching solenoid can act as a remote disconnect switch.


All products listed in this section can be found in Section H of the Cole Hersee D-275 CATALOG.
  • 12V Grounded intermittentSome switches are designed for infrequent (or intermittent) use. Devices such as solenoids may need a cooling period before they should be re-actuated. Rating a switch for intermittent use typically allows it to operate at a higher current than might otherwise be recommended. See CONTINUOUS. You can use a Continuous Duty Solenoid in place of an Intermittent Duty Solenoid, but it would have a shorter life expectancy compared to the purpose-built Intermittent Duty Solenoid. DO NOT use an Intermittent Duty Solenoid in place of a Continuous Duty Solenoid! duty with resistor shorting circuitA closed path (or loop) of electrically (or electromagnetically) connected components or devices that is capable of current flow. Typically consists of loads, sources, conductors, and circuit protection (circuit breakers and fuses). The path must be continuous and closed. .
  • With a resistor shorting solenoidAn electromechanical device (or relay) that is used to switch large currents. It consists of a coil of wire and a moving contact that makes an electrical connection when the coil of wire is energized. Cole Hersee manufactures over 50 kinds of solenoid. See # 24059, stud 3 is Normally open, and becomes common with 1 and 4 when the solenoid is energized. Commonly used in engine starting applications.
  • 750A make, 100A break, 10sec On, 20min Off.
  • Contacts: Copper.
  • Terminals: Copper. Small terminals are 10-32 thread. Large contact terminals are 5/16" -24 thread. Hexnuts and lockwashers are included.
  • Bracket mounting holes 5/16 x 19/32,” 2 13/64" on centers (7.9 x 15.1, 56.0mm)
  • Plated steel housing.
Description Intermittent Duty Solenoid
Special applications Universal, commonly used in engine starting
Insulated/Grounded Grounded
NO/NC normally open
Circuitry SPST
Contacts copper
Housing plated steel
Voltage rating 12V
Terminals copper; 10-32 thread and 5/16"-24 thread. Brass hex nuts and lock washers included
Bracket Straight
Bracket mounting Holes 5/16" x 19/32", 2-13/64" on center
Breather hole no
UL Marine & CE ISO 8846 Marine Not listed

COLE HERSEE 24103 Cross Reference

We have 1 alternatives for the 24103 by COLE HERSEE:

Cole Hersee® is highly valued in the heavy duty truck industry. It is a leading manufacturer of heavy-duty battery master switches that are widely used as OE equipment by leading heavy-duty vehicle manufacturers. These switches are essential safety components for trucks as they help prevent theft, tampering, electrical fires, and battery drain. Founded in 1924, Cole Hersee is committed to improving vehicle safety by partnering with ECCO Safety Group Australia (ESGA) to establish and implement safety standards for trucks that drive onto mining sites. Its products are also manufactured in its ISO 9001:2008-certified facility and undergo strict testing to ensure safety and reliability.

Don't know your part number?

Take a photo and we'll identify it!

Recommended Products

More from COLE HERSEE (Browse all)